Great River Style Arch Built with plenty of extra support for towing. SHIPPING INCLUDED TO LOWER 48 STATE DESTINATIONS CALL FOR SHIPPING COST QUOTE TO LOCATIONS OUTSIDE THE LOWER 48 STATES If you have a river boat you have already seen our top quality arches. Our arches work well on most aluminum river boats such as Bentz Boats, Koffler Boats, Alumaweld, Hewescraft, Bratt Jet, Rogue, RiverPro, RiverHawk, Thunderjet, Boulton, North River, Weldcraft, KingFisher Lund, Duckworth, Starcraft, Alumacraft, and Rockproof just to name a few. If you are interested in one of our arches just give us a call 586-255-0212 Fits Most Boats. Adjust from 48" up to 115" Wide Comes with 4 Bolt on Rod Holders, Break Away Mounts, and Tow Boss. Built from 2" Schedule 40 Pipe with 1" Schedule 40 accent parts. Designed to fold down in a matter of minutes. Hollow tube all the way through to run and hide wires. You will need to drill an access hole near the bottom of one of the legs above the mounts approximate 1" above the top of the mounts when the mounts are fully seated in the tube and an exit hole near where you will be mounting your lights on the top cross tube. Insert a wire during assembly to serve as a cord for pulling the wires through the tube when the assembly is complete. We recommend using a good quality automotive anti-seize compound on all threads. While not mandatory this additional step will save you work later should you decide to move or disassemble rod holders etc. Two different style mounts "side and deck". Mounting holes are .278 diameter and are sized for 1/4 20 screws. Stainless steel screws are recommended. Also backing plates are recommended. You may need to cut small amounts of flotation foam under the gunnels on some boats.When you pick an approximate width you will have 5" of adjustment in and out. Unit weighs 70lbs. Assembly required. Bolts,nuts and lock washers for holding the bases to the deck or cabin side are not included due to the wide variety of hull and or cabin thicknesses. Purchase the stainless steel bolts, nuts, fender washers and lock washers locally. You wonder if this arch is strong enough, here's what one customer said recently "Thank you very much!! I am thrilled with the arch and its sturdiness. Ive had other arches in the past and this one beats them by far." ***Select standoff option for increasing strength of side mounts. More terrific options for your arch, Click on the image or part no. below. (Note: Grab Bars do not fit the FOS-320 Arch) . 107 100-17 100-13 100-20 100-15 100-32 100-21 Captains Pkg 109 180 FOS-22 100-19 100-26 108-2x4 100-24 Limited Gunwale Mount Limited Gunwale Mount Shown Captains Package upgrades to a total of = BRONZE Economy Package 2 Additional Bolt on Rod Holders Part# 107 ( 2 with 1.91" clamps) 2 Additional Bolt on Rod Holders Part# 107 ( 2 with 2.375" clamps) 1 Net Holder Part# 109 with 1.91" clamps SILVER Standard Package 2 Additional Bolt on Rod Holders Part# 107 ( 2 with 1.91" clamps) 2 Additional Bolt on Rod Holders Part# 107 ( 2 with 2.375" clamps) 1 Net Holder Part# 109 with 1.91" clamps 2 Quick Swivel Rod Holders RH with 1.91" Clamps 1 Light Bracket Set (2 light brackets) with 1.91" Clamps GOLD Premium Package 2 Additional Bolt on Rod Holders Part# 107 ( 2 with 1.91" clamps) 2 Additional Bolt on Rod Holders Part# 107 ( 2 with 2.375" clamps) 2 Net Holder Part# 109 with 1.91" clamps 2 Quick Swivel Rod Holders RH with 1.91" Clamps 1 Light Bracket Set 100-13 (2 light brackets) with 1.91" Clamps 2 Marine Lights 100-20 2 Cup/Drink Holders 100-17 with 1.91" Clamps 2 Universal Multi-Mounts 100-36 with 1.91" Clamps . Here are some photos of my Crestliner 1850 Superhawk with the Fish-on Sports Jr.river crossover arch with visor. I installed this setup by myself but it would be easier at times with two people. The rig is very solid and it has the ski tow lug on top. Very,very well made. I have not come across anything quite as nice as this. Thank you, Todd K. Assembly Directions:
Great River Style Arch Built with plenty of extra support for towing. SHIPPING INCLUDED TO LOWER 48 STATE DESTINATIONS CALL FOR SHIPPING COST QUOTE TO LOCATIONS OUTSIDE THE LOWER 48 STATES If you have a river boat you have already seen our top quality arches. Our arches work well on most aluminum river boats such as Bentz Boats, Koffler Boats, Alumaweld, Hewescraft, Bratt Jet, Rogue, RiverPro, RiverHawk, Thunderjet, Boulton, North River, Weldcraft, KingFisher Lund, Duckworth, Starcraft, Alumacraft, and Rockproof just to name a few. If you are interested in one of our arches just give us a call 586-255-0212 Fits Most Boats. Adjust from 48" up to 115" Wide Comes with 4 Bolt on Rod Holders, Break Away Mounts, and Tow Boss. Built from 2" Schedule 40 Pipe with 1" Schedule 40 accent parts. Designed to fold down in a matter of minutes. Hollow tube all the way through to run and hide wires. You will need to drill an access hole near the bottom of one of the legs above the mounts approximate 1" above the top of the mounts when the mounts are fully seated in the tube and an exit hole near where you will be mounting your lights on the top cross tube. Insert a wire during assembly to serve as a cord for pulling the wires through the tube when the assembly is complete. We recommend using a good quality automotive anti-seize compound on all threads. While not mandatory this additional step will save you work later should you decide to move or disassemble rod holders etc. Two different style mounts "side and deck". Mounting holes are .278 diameter and are sized for 1/4 20 screws. Stainless steel screws are recommended. Also backing plates are recommended. You may need to cut small amounts of flotation foam under the gunnels on some boats.When you pick an approximate width you will have 5" of adjustment in and out. Unit weighs 70lbs. Assembly required. Bolts,nuts and lock washers for holding the bases to the deck or cabin side are not included due to the wide variety of hull and or cabin thicknesses. Purchase the stainless steel bolts, nuts, fender washers and lock washers locally. You wonder if this arch is strong enough, here's what one customer said recently "Thank you very much!! I am thrilled with the arch and its sturdiness. Ive had other arches in the past and this one beats them by far." ***Select standoff option for increasing strength of side mounts. More terrific options for your arch, Click on the image or part no. below. (Note: Grab Bars do not fit the FOS-320 Arch) . 107 100-17 100-13 100-20 100-15 100-32 100-21 Captains Pkg 109 180 FOS-22 100-19 100-26 108-2x4 100-24 Limited Gunwale Mount Limited Gunwale Mount Shown
Hollow tube all the way through to run and hide wires. You will need to drill an access hole near the bottom of one of the legs above the mounts approximate 1" above the top of the mounts when the mounts are fully seated in the tube and an exit hole near where you will be mounting your lights on the top cross tube.
Insert a wire during assembly to serve as a cord for pulling the wires through the tube when the assembly is complete.
We recommend using a good quality automotive anti-seize compound on all threads. While not mandatory this additional step will save you work later should you decide to move or disassemble rod holders etc.
Two different style mounts "side and deck". Mounting holes are .278 diameter and are sized for 1/4 20 screws. Stainless steel screws are recommended. Also backing plates are recommended. You may need to cut small amounts of flotation foam under the gunnels on some boats.
