Cisco complete planer system rail pulley mount. (SHIPS FREE IN LOWER 48 STATES) Includes: 2 each PMELR Cisco - Planer Board Electric Drive Reel for Custom Applications SPECIFY O.S. DIAMETER RAIL SIZE IN NOTES AT CHECKOUT WHEN ORDERING, clamps fit from 7/8" to 1 1/2" larger sizes also available email us to make sure the size is available Planer Board Electric Drive Reel for Custom Applications Includes: 6" solid aluminum reel, line guide, variable clutch, aluminum clutch knob, high torque electric motor with modified output shaft, universal mounting bracket, vee clamp (capable of clamping 7/8 in. thru 1-1/2 in. diameter); larger vee clamps and selective radius clamps are also available at an additional cost. Control sold separately. FEATURES: electric drive motor, line guide and vee clamp may be rotated to other positions to accommodate your mounting requirements. The vee clamp can be located on the same side which the motor is mounted as long as the motor is rotated for their clearance. 2 each PMSCP Cisco - Single Planer Pulley with Clamp If you are looking to set up your boat in a way slightly different than traditional rigging than this unit may be exactly what you have been seeking! Our rail clamps can fit any rail from 7/8” to 1½” in diameter (larger clamps are also available upon request) and the entire mounting system is machined from solid aluminum. If rails are over 1 1/3" in diameter a $18 up charge may apply. Our pulley’s are constructed with solid aluminum side plates, hard anodized aluminum sheave, stainless steel ball bearings, and bolted together with stainless steel hardware. The sheave is recessed to prevent the line from being captured between the side plate and sheave. The 12/0 swivel is rated by the manufacturer at 1500 lbs (this swivel is constructed in the USA). 2 each PMECT Cisco - Electric Control for Planer Board Applications The electric control box is constructed of polycarbonate material and has a waterproof enclosure with stainless steel screws. The wire fittings have rubber inserts to grip and seal the wire as it enters the control box to ensure a watertight seal. Dimensions are approximately 3” x 3” x 2”. Included in the control is a resettable push button 8 amp breaker with a waterproof boot. There is a 3-way switch (on-off-on) which controls the spooling rotation of the reel and also includes a switch guard and a waterproof boot. The wire is 14 Gauge Fine Stranded low voltage copper wire. The jacket of the wire is UV/water/oil resistant. We provide 11 feet of wire from the boat power supply to the control box and 22 feet of wire from the control box to the electric drive reel. Extra lengths are available at customer request (additional charges may apply). Does not include wire/line
2 each PMELR Cisco - Planer Board Electric Drive Reel for Custom Applications SPECIFY O.S. DIAMETER RAIL SIZE IN NOTES
AT CHECKOUT WHEN ORDERING, clamps fit from 7/8" to 1 1/2" larger sizes also available email us to make sure the size is available
Planer Board Electric Drive Reel for Custom Applications Includes: 6" solid aluminum reel, line guide, variable clutch, aluminum clutch knob, high torque electric motor with modified output shaft, universal mounting bracket, vee clamp (capable of clamping 7/8 in. thru 1-1/2 in. diameter); larger vee clamps and selective radius clamps are also available at an additional cost. Control sold separately.
FEATURES: electric drive motor, line guide and vee clamp may be rotated to other positions to accommodate your mounting requirements. The vee clamp can be located on the same side which the motor is mounted as long as the motor is rotated for their clearance.
If you are looking to set up your boat in a way slightly different than traditional rigging than this unit may be exactly what you have been seeking!
Our rail clamps can fit any rail from 7/8” to 1½” in diameter (larger clamps are also available upon request) and the entire mounting system is machined from solid aluminum. If rails are over 1 1/3" in diameter a $18 up charge may apply.
Our pulley’s are constructed with solid aluminum side plates, hard anodized aluminum sheave, stainless steel ball bearings, and bolted together with stainless steel hardware. The sheave is recessed to prevent the line from being captured between the side plate and sheave. The 12/0 swivel is rated by the manufacturer at 1500 lbs (this swivel is constructed in the USA).
The electric control box is constructed of polycarbonate material and has a waterproof enclosure with stainless steel screws. The wire fittings have rubber inserts to grip and seal the wire as it enters the control box to ensure a watertight seal. Dimensions are approximately 3” x 3” x 2”.
Included in the control is a resettable push button 8 amp breaker with a waterproof boot. There is a 3-way switch (on-off-on) which controls the spooling rotation of the reel and also includes a switch guard and a waterproof boot.
The wire is 14 Gauge Fine Stranded low voltage copper wire. The jacket of the wire is UV/water/oil resistant. We provide 11 feet of wire from the boat power supply to the control box and 22 feet of wire from the control box to the electric drive reel. Extra lengths are available at customer request (additional charges may apply).